Embroider on socks

• Quality: draft

• Difficulty: beginner

The problem

In order to embroider on a sock, one has to make sure that the machine only stitches on one side of the sock.

This is a very easy task if your machine has a small free arm, like all professional and semi-professional machines do. Sometimes, small frames must be bought as an add-on, e.g. the "Compact Frame Set" with the "E" Frame holder for the PR1050X.

Small embroidery frames for the PRX1050X: Frame V (3.3 x 7.5 cm) and Frame 50

Stitching a sock with the small vertical 33x75mm Brother V frame

In this article we will present three methods. The first only requires safety pins, the 2nd "sock tool" method and the 3rd "sock frame" a 3D printer or a laser cutter. The "sock frame" method also requires measuring out a hoop and changing parameters of a 3D model.

Embroider a sock using safety pins

The safety pin method is fairly easy to achieve, but it takes some time. The basic principle is to pin a roughly 5cm x 5cm area to the stabilizer for embroidery and pull the tissue that would sit underneath away.

1) Hoop a strong stabilizer, preferably polyester. Tighten well (but without breaking the frame).

2) Optional: If your frame is thin or broken, it is advisable to fix the stabilizer with safety pins to the frame (c.f. the pictures below where you can see that the stabilizer has been attached at the top and bottom).

3) Attach the top of the sock like in the next picture below

• Start by fixing the 2 corners of the side you want to embroider, so the top/front of the sock.
• Then fix, the 2 opposite corners as in the following image.
• In both cases, pull the sock slightly, but not too much, otherwise the embroidery will fold.

Attach the sock to the four corners of the hole with safety pins.

4) Pull the surface to be embroidered in three directrions and fix with safety pins.

• It is important that the fabric to be embroidered is flat and that nothing gets stuck underneath (otherwise you won't be able to fit in your sock). Pinch the fabric about halfway between the bottom (c.f. point 3) and the top and pull well !
• To attach this pulled embroidery surface you need at least three pins: One at the bottom, one on the left and one on the right. The following picture already shows a pin on the left and on the right. On the left you can see the head of a pin that was used in step 3.

Pull the sock down and out and secure with safety pins.

Below is a decent hooping result (our second attempt). We can see the surface to be embroidered. Underneath there is only the stabilizer.

Pull the sock down (left in the picture) and secure with safety pins.

5) Stitch ....

• 

  Alien in progress

• 

  DNA in progress

Advice:

• Obviously it is difficult to do precision embroidery. So you have to either work with airy designs or overlap embroidery surfaces to avoid gaps. Also avoid too tight satin stitches (2mm is a minimum).
• Do not exceed a surface of 5x4cm for an adult sock.

Seen from the bottom of the frame. The tension is low, but OK for "safe" designs

Results:

• 

  DNA embroidered on an elastic cotton sock

• 

  Alien embroidered on an elastic cotton sock

Embroider with the sock tool

The sock tool does basically the same thing as the safety pin method. It clears a 50 x 50 mm space for embroidery. Instead of pulling various bits of the sock with safety pins, you wrap the sock around the tool as we shall explain:

thumb|right|200px|birds on socks

Step 1: Design

You must adapt your design to the size of the hole. We suggest to respect a safety margin of at least 1.25cm on each side, that is length = hole size - 2.5cm.

• For a 70 x 70 tool, do not exceed 45 x 45mm
• For a 60 x 60 tool, keep it down to 35 x 35 mm

For additional safety we also encourage stitching some kind of fixing line first

Step 2: Hooping

Select the right size, e.g. the default settings generate a tool with a 7cmx7cm hole, a 1cm border and 3.7cm Wings and that fits medium size well

Insert the sock

• Push the upper end of the sock through the mouth

Attach the sock to the right side

Attach to the left side

Pull tissue underneath over the wings

• Avoid damaging the sock

Pull the sock down

• gently pull the sock through the hole

Adjust

• Make adjustements until the surface to embroider looks good

Flatten

• Pull addition tissue through the sock hole

Step 3 Prepare the hoop

• Insert autoadhesive stabiliser sticky side up into a hoop that is bigger than the sock tool
• Remove the protection of the stabiliser
• Put the sock tool as much in the center of the hoop as you can
• (Option) secure with 2 safety pins

Step 4 Position the design

• Insert the hoop into the machine and make sure that machine is aware of the hoop size
• Load the design into the machine
• Verify hoop size again and change if necessary (some machines do not behave)
• Position the design so that its center is the center of the hole.
• Make sure that your machine stitches the design around the center.
• Verify if your design is well positioned by any offered means, e.g. have the machine outline the design. Adjust if necessary, i.e. move the design in the control screen.

Step 5 Stitch

• If you are confident of your positioning, stitch a hold down rectangle. Before doing so make sure that the line is close to the design (that can be defined in the settings). Else do not do that, since your foot or needle may run into a wall.