Adafruit Sensors

This article or section is currently under construction

In principle, someone is working on it and there should be a better version in a not so distant future.
If you want to modify this page, please discuss it with the person working on it (see the "history")

Introduction

In this article,we propose an overview of the Adafruit Circuit Playground Express (CPX) built-in sensors. This aim of this page is to show you how to leverage them in MakeCode. So, if you are not familiar with MakeCode, we advise to have a look on MakeCode page in this wiki.

The CPX built-on sensors available are :

• Buttons
• Capacitive touch
• Light sensor
• Accelerometer
• Microphone
• Switch button
• Thermometer
• Infrared Transceiver

Coding sensors in MakeCode

In MakeCode, there are two means to read the code : through events or by reading live data:

• Events: code runs when an event is detected. For example, the OnShake event runs code when a certain type of shaking is detected by the accelerometer.
• Live data: live reading of the sensor data without a particular event taking place. For example,Rotation gets a immediate reading from the accelerometer.

You will find below the 2 style of programming with sensors : through events (on left of the picture below) and through live data (on right on the picture below).

Sensors

Buttons

Buttons A & B

On the CPX, there are 2 buttons : Button A or Button B. The two buttons could be coded together Button A + B.

Event

the OnEvent block allows to respond to action (click, long click and other events.

Live data

the button can be read in live by using the input IsPressed that is to say the code check if the button is pressed. You can also used the input WasPressed in situations in which the program have a risk to busy when the user clicked. In this case, the code check if the button was clicked earlier.

Example : The click on button A is used to play a sound. The state of button A is checked in a forever loop to switch between red (if button A is pressed) and green (if nothing happens).

Capacitive touch

Capacitive touch pins

On the CPX, there are 7 capacitive pins (A1, A2, A3, A4, A5, A6 and A7). They can be used as buttons (like buttons A or B).

Event

The pins can be used as touch inputs, the code use them like buttons. Instead of saying Button A or Button B as the input source, use a pin name like A1.

Live data

you can read the live button status using input IsPressed or WasPressed.

Example : An event on pin A4 is used to show pixels animation and the state of pin A7 is checked in a forever loop to switch between blue or red on the neopixels.

Light sensor

Light sensor

On the CPX, you have 1 light sensor which allows to run code when the brithgness change.

Event

By using the on light condition, the sensor allows to run code.

Live data

The light level returns the light intensity : from 0 (no light) to 255 (max light).

Example : Using the on light event to run a sparkle animation.

Accelerometer

The CPX has one accelerometer that runs code when acceleration happens on axes X (left to right), Y (bottom to top), Z (aligned with the gravity). Please see the picture below.

Accelerometer

x, y, z axis

Events

The input on Gesture enable to program adafruit to run a code folowing a certain event such shake, freefall or orientation events.

Live data

an acceleration input can return the acceleration value (in milli-g, e.g 1/1000 of a g) according to direction (on x, y or z axis) or the combined force in all directions.

Example : Using a shake to play a sound (event). A forever loop can display the accelerometer reading (live data).

Microphone

The CPX has one microphone that runs code when a sound happens.

Events

The on loud sound event detect a peak in the sound level, e.g a hand clapping. You can change the lound treshold by using the set sound to sound level (e.g https://learn.adafruit.com/make-it-sense/makecode-3).

Live data

The sounf level block return the sound intensity from silent (0) to 255 (very loud).

Example : An sound variation can play a music; a forever loop can continuously display the sound level.

Switch button

The CPX has one switch button which have 2 positions : left or right. This button can be very useful to create some on/off programs.

Event

The on switch moved input enable to run code when the switch button is moved to the left position or to the right position.

Live data

The switch right block (in input) indicates if the switch is on the right position.

Example : events can be play different animations if the switch button is on the left or on the right. A forever can play an animation if the switch is on the right position and no animation if the switch is on the left.

Thermometer

The CPX has a thermometer that can track the ambient temperature (in Celcius or Fahrenheit degrees).

Events

The event on temperature (condition changed) runs code when temperature changes from hot to cold or from cold to hot.

Live data

The temperature block return the current temperature by checking how hot its computer chips are.

Exmample : If the temperature change over 15°C, a sound is playing. A forever loop can graphs the current temperature using the LEDs over 20°C.

Infrared transceiver

The CPX have an onboard infrared transceiver (i.e transmitter and receiver) which allow to communicate data between CPXs.

Events

The [https://makecode.adafruit.com/reference/network/on-infrared-received-number On infrared received

Live data

no use.

Links

At Adafruit

• Sensors in MakeCode

Aknowledgement

Pictures as well as some text was reproduced from the Adafruit circuit playground express documentation. Some pictures are available under a CC BY-NC-SA license. Others are copyright AdaFruit and "all rights reserved" and reproduced with permission. Before you reuse any picture from this website, make sure to look at the license information.

For more information about using Adafruit, see https://learn.adafruit.com.