Adafruit Circuit Playground

There are TWO types of circuit playgrounds : one classic and one express. The classic version can run Arduino and Code.org and the express version can run MakeCode, CircuitPython, Arduino, and Code.org CS discoveries. We present here the Circuit playground Express

Introduction

AdaFruit Circuit Playground Express'. Source: Flickr of AdaFruit

Circuit Playground Express (alias "CPX") is a board of the Adafruit Wearables line of of e-textile products. This board is beginner friendly since it can (also) be programmed with MakeCode and since it includes sensors, 10 LEDs, 2 push buttons, etc. and a loudspeaker in addition to the basic components (microcontroller, connectors, etc.). A new version, called Circuit Playground Bluefruit, includes Bluetooth and is under development, and as of Sept 2019 is in alpha testing.

The board is rather large and heavy compared to Adafruit's FLORA and GEMMA. However, this is compensated by it's feature rich design and ease of use.

50.6mm / ~2.0"
Weight: 8.9g

The board can be bought in three packaging variants:

Circuit Playground Express $25, includes just the board
Circuit Playground Express - Base Kit, $30, includes a battery and USB cable.
Circuit Playground Express Advanced Pack, $100, includes 2 Playground express, threads, needles, alligator clips, a servo motor, NeoPixels, etc.

For a class, it's probably best to buy Base Kits ($30), either a few Advanced Packs or other FLORA extension elements, and finally some simple boards (for replacements or projects that include more than one board).

Extras

Enclosure

The board

General presentation

Below is a picture of an Adafruit Circuit Playground Express

AdaFruit Circuit Playground Express'. Photo source: Adafruit Flickr

Components and layouts

According to the product page (retrieved Aug 26, 2019), this board includes the following elements which are explained in detail in the guided tour.

Processor and basics

ATSAMD21 ARM Cortex M0 Processor, running at 3.3V and 48MHz
2 MB of SPI Flash storage (i.e. a tiny disk drive), used primarily with CircuitPython to store code and libraries.
A JST battery connector (alternatively, the board also can take power from the USB connector).
Green "ON" LED so you know its powered (top left)
Red "#13" LED for basic blinking
Reset button (in the middle)
A total of 14 input/output pads ("the holes")

Connectivity:

MicroUSB port for programming and debugging. It can act like a serial port, keyboard, mouse, joystick or MIDI!
Infrared receiver and transmitter - can receive and transmit any remote control codes, as well as send messages between Circuit Playground Expresses. Can also act as a proximity sensor.
14 "alligator" clip pads: a wide range of power pins, I2C, UART, Analog In, Digital In/Out, PWM, and Analog Out.

Output:

10 x mini NeoPixels. These programmable LEDs can display any color. They are also used for some status information: when the bootloader is running they will turn green, or if it failed to initialize USB when connected to a computer, they will turn red).
1 Mini speaker with class D amplifier (7.5mm magnetic speaker/buzzer). It is connected to to the A0 analog output pin.

Input and sensors:

1 Temperature sensor
1 Light sensor. Can also act as a color sensor and pulse sensor.
1 Sound sensor (MEMS microphone)
1 Motion sensor, i.e. a LIS3DH triple-axis accelerometer with tap detection, free-fall detection.
2 x Push buttons, labeled A and B
1 x Slide switch
7 of the 8 GPIO pads have capacitive touch (A1.A2, A3, A4, A5, A6, A7)

Pads' General Purpose Input Ouput (GPIO) pads

All the 8 GPIO pads (A0 to A7) can be used as digital inputs, digital outputs, for LEDs, buttons and switches. In addition, all can be used as analog inputs (12-bit ADC).

Power pads

There are 6 power pads

Notice: I have to figure out what some of the various pins/pads really do (this is my first electronics experience....)

Packaging

As explained above, the Circuit Playground Express is available as single component ($25), as basic kit (including a USB cable, needles, AAA-battery pack, lithium battery, and some thread, $30) and as Circuit Playground Express Advanced Pack ($100).

Adafruit Circuit Playground Express Base Kit, as of Aug 2019

Add ons

Circuit Playground TFT Gizmo - Bolt-on Display + Audio Amplifier

Besides various Adafruit components that can be added, e.g. Neopixel strips, there are:

Circuit Playground TFT Gizmo - Bolt-on Display + Audio Amplifier ($19.95). This "thing" can be bolted to a Playground Express. Quote: Once attached you'll get a 1.54" 240x240 IPS display with backlight control, two 3-pin STEMMA connectors for attaching NeoPixel strips or servos, and a Class D audio amplifier with a Molex PicoBlade connector that can plug one of our lil speakers. As of Stp. 2019, the product is sold, but still in alpha.

Programming the board

To compile and upload a program to the controller

Open
Makecode for Circuit Playground Express
Connect the board with the USB cable
Press the reset button in the middle(for a while). See the schema above if you cannot find it..
When it turns green, you can download the code from your browser window.

Example

Clap hands code example: Based on the "clap lights" example at Makecode.adafruit.com

Javascript version

Notice how the RDG colors are defined. E.g. red (CSS #FF0000) becomes 0xff0000

input.onLoudSound(function () {
    light.setBrightness(20)
    for (let i = 0; i < 4; i++) {
        light.setAll(0xff0000)
        pause(200)
        light.setAll(0x000000)
        pause(200)
    }
    light.setPixelColor(0, 0x00ff00)
    light.setPixelColor(9, 0x00ff00)
})

Result after clapping

Clap hands code example (see the Adafruit on the right of the screen)

Links

Official tutorials

Adafruit Circuit Playground Express documentation

Adafruit Circuit Playground Express (several pages)
Adafruit Circuit Playground Express (in one HTML page)
Adafruit Circuit Playground Express (all-in-one PDF file]

Tutorials

Many hands-on tutorials are available through the online editor, e.g. the clap lights tutorial (a simpler version of our clap hands example)

https://makecode.adafruit.com/

Acknowledgement

Pictures as well as some text was reproduced from the Adafruit circuit playground express documentation. Some pictures are available under a CC BY-NC-SA license. Others are copyright AdaFruit and "all rights reserved" and reproduced with permission. Before you reuse any picture from this website, make sure to look at the license information.

For more information about using Adafruit, see https://learn.adafruit.com.

Adafruit Circuit Playground

Contents

Introduction