Trotec Speedy 100R: Difference between revisions

The educational technology and digital learning wiki
Jump to navigation Jump to search
 
(33 intermediate revisions by 2 users not shown)
Line 107: Line 107:


=== Print ===
=== Print ===
* Calibrate the height
* Make sure that the material to cut is flat (important for textiles). Otherwise either increase power or weigh down the material. You also can use "Seklema Haftmatten" (Trotec Shop)


* <code>Establish Connection</code> in JobControl
* <code>Establish Connection</code> in JobControl
Line 113: Line 117:


* Press <code>START</code> button (green arrow) in Job Control.
* Press <code>START</code> button (green arrow) in Job Control.


=== Wait ===
=== Wait ===
Line 168: Line 171:
* In the '''Printing Preferences''' window, make sure that you are in expert mode (select the ''general'' tab)
* In the '''Printing Preferences''' window, make sure that you are in expert mode (select the ''general'' tab)


'''(3) Steps 3 and 4: Define material settings and process options
'''(3) Steps 3 and 4: Define material settings and process options'''


In the ''Print tab'' you then must define the print process:
In the ''Print tab'' you then must define the print process:
Line 190: Line 193:


<code>Relief</code>
<code>Relief</code>
: {{quotation|This type of processing controls the laser power depending on the gray-scale value of the graphic.}} <ref name="operationmanual">Trotec (2015), ''Operation Manual Trotec JobControl. Basic, Advanced, Expert''. Retrieved from https://www.troteclaser.com/fileadmin/content/images/Contact_Support/Manuals/JobControl-Manual-EN.pdf, page 31</pref>
: {{quotation|This type of processing controls the laser power depending on the gray-scale value of the graphic.}} <ref name="operationmanual">Trotec (2015), ''Operation Manual Trotec JobControl. Basic, Advanced, Expert''. Retrieved from https://www.troteclaser.com/fileadmin/content/images/Contact_Support/Manuals/JobControl-Manual-EN.pdf, page 31</ref>


This configuration requires 256 gray scale (8-bit). Lighter means less power and darker means more power.
This configuration requires 256 gray scale (8-bit). Lighter means less power and darker means more power.
Line 257: Line 260:
=== Material settings table ===
=== Material settings table ===


Since we just started with laser cutting, please consider the following very provisional ! In principle, the settings should work for a Trotec 50W CO laser... but they are by no means optimal (yet).
Since we just started with laser cutting, please consider the following very provisional ! In principle, the settings should work for a Trotec 50W CO laser... but they are by no means optimal (yet). Various materials that one could use with a CO2 Laser like the Speedy 100 are described in the [[laser cutting]] article.


Often there are different solutions that lead to similar results. Remember that laser power received is a function of power and speed, and pulse (in case of cutting)
Often there are different solutions that lead to similar results. Remember that laser power received is a function of power and speed, and pulse (in case of cutting)
Line 272: Line 275:
! Engraving power
! Engraving power
! Engraving speed
! Engraving speed
!N engraving passes
! Engraving resolution
! Engraving resolution
! Notes
! Notes
Line 282: Line 286:
| 50
| 50
| 100
| 100
|2
| 500
| 500
| 2 passes reduced burning
| 2 passes reduced burning
Line 292: Line 297:
| 50
| 50
| 100
| 100
|
| 500
| 500
|
|-
|Maple Wood 5mm
|80
|1
|1000
|1
|100
|70
|2 (is prettier)
|500
|To create darker engraving, reduce speed a bit. To go deeper, do 2 passages.
|-
|Plywood poplar 3mm
|100
|1.1
|1000
|1
|100
|100 (70)
|1 (2 at 70 is prettier)
|600
|Very easy, since weak material.
|-
|Plywood poplar 5mm
|100
|0.9 (0.8 if uneven)
|1000
|1
|100
|100 (70)
|1 (2 at 70 is prettier)
|600
|Poplar plywood is not very strong, but easy to engrave and to cut.
|-
|Plywood linden Creality (tilleuil) 10mm
|100
|0.32
|1000
|2
|100
|80
|2
|500
|
|
|-
|-
| Plywood birch 4mm
| Plywood birch 4mm
| 100
| 100
| 1.3
| 1.2 (for large objects maybe a bit less)
| 1000
| 1000
| 1
| 1
| 80 (ou 2x à 50)
| 80 (or better 2 at 60)
| 100
| 100
|
| 500
| 500
| Attention aux flammes
| Birch plywood is strong quality but difficult to laser, in particular larger than 4mm sizes.
Watch out for flames
|-
|-
| Plywood birch 6.5mm (difficult)
| Plywood birch 6.5mm (difficult)
Line 312: Line 364:
| 60 (2x)
| 60 (2x)
| 70
| 70
|
| 500
| 500
| Set correction to 15. These are minimal settings to test and some larger cuts with lots of details could fail. Result is very black and requires washing. You could put some painters tape on the cut lines to avoid blackening of the surface.  
| Set correction to 15. These are minimal settings to test and some larger cuts with lots of details could fail. Result is very black and requires washing. You could put some painters tape on the cut lines to avoid blackening of the surface.  
Line 322: Line 375:
| 80
| 80
| 70
| 70
|
| 500
| 500
| Result is always very black and needs washing. More pulse and more power doesn't change that much. Result looks similar and flames are a bit bigger and will destroy thin elements. Also try '''three passes with a bit less power or higher speed'''.
| Result is always very black and needs washing. More pulse and more power doesn't change that much. Result looks similar and flames are a bit bigger and will destroy thin elements. Also try '''three passes with a bit less power or higher speed'''.
|-
| Plexi 10mm
| 100
| 0.5
| 10000
| 2
| 80
| 100
|
| 500
| Better, position the plate on top of some wooden blocks, not directly on the grid.
|-
| Plexi 5mm
| 100
|0.8
| 4000
|2
| 80
| 100
|
| 500
| Better, position the plate on top of some wooden blocks, not directly on the grid.
|-
|-
| Plexi 4mm  
| Plexi 4mm  
Line 332: Line 408:
| 80
| 80
| 100
| 100
|
| 500
| 500
| Position the plate on top of some wooden blocks, not directly on the grid.
| Position the plate on top of some wooden blocks, not directly on the grid.
Line 342: Line 419:
| 80
| 80
| 100
| 100
|
| 500
| 500
|
|
Line 352: Line 430:
| 80
| 80
| 100
| 100
|
| 500
| 500
|
|
|-
| Trolase Textures 1.6 mm matte
| 50
| 0.8
| 4000
| 1
| 100
| 50-60
|
| 600
| This is a bi-color acrylic plastic from TroTec, much cheaper than Plexiglass, i.e. a 60.5 x 30.5cm costs 12.20 CHF. '''Extra settings''': Z-offset is 2 (as opposed 0) in order to make the laser a bit thicker. (2) Start position at bottom (right-click, select properties)
|-
|Trolase 0.8 mm smooth
|50
|1.5
|1000
|
|100
|50-60
|
|600
|Z-offset = 2. Verify.
|-
|-
| Ondulated Cardboard
| Ondulated Cardboard
Line 362: Line 463:
| 60
| 60
| 100
| 100
|
| 1000
| 1000
| Rough settings, thickness and density is widely different. If the first layer is thicker you can go with engraving P = 80
| Rough settings, thickness and density is widely different. If the first layer is thicker you can go with engraving P = 80
|-
| Ondulated Cardboard (cuts)
| 20
| 1
| 1000
| 1
| 7
| 3
|
| 5000
| Rough settings. Engraving parameters are meant for engraving lines, i.e. cuts defined with another color ! Both speeds could be higher. Please test first with a small design.
|-
|-
| Thick paper 0.25mm ?
| Thick paper 0.25mm ?
Line 372: Line 485:
| 80
| 80
| 100
| 100
|
| 1000
| 1000
|
|
|-
| Gunold Step
| 22
| 1.9
| 1000
| 1
|
|
|
| 1000
| Special embroidery textile for creating patches. Set Power to 30 (instead of 22) for larger pieces. The tissue can warp and the laser will be less focused and therefore less strong
|-
|-
| Cotton (pants)
| Cotton (pants)
| 30
| 30
| 3
| 3
| 1000
| 1000-3000
| 1
| 1
| 90
| 20
| 100
| 100
| 1000
|
| Test this, engraving effects differ for each type of cotton. I made a Halloween mask from a cut off pant leg)
| 200-300
| Test this, engraving effects differ for each type of cotton. I made a Halloween mask from a cut off pant leg). Make sure to work with a low DPI (else you can create cuts that will appear later). In addition use an offset of 2 to 20mm (defocalize) and turn off the ventilator.
|-
|-
| Wood Wine box 7mm
| Wood Wine box 7mm
Line 392: Line 518:
| 60
| 60
| 70
| 70
|
| 500
| 500
|
| Nice and easy, if the wood is light. Testing required
|-
|Heavy Wood Wine box 9.5mm
|100
|0.35
|2000
|3
|40
|100
|2
|500
|Some use tougher wood, so it won't be nice and easy. Testing required. Maybe 0.23 for cutting speed.
|-
|-
| Anodized aluminum, e.g. Laptops (this needs to be tested !)
| Anodized aluminum, e.g. Laptops (this needs to be tested !)
Line 402: Line 540:
| 100 ?
| 100 ?
| 100
| 100
|
| 500
| 500
| Not tested, probably also depends a lot on the coating. Use weaker settings for plastic cases !!
| Not tested, probably also depends a lot on the coating. Use weaker settings for plastic cases !!
Line 407: Line 546:
| Material
| Material
|  
|  
|
|
|
|
|
Line 416: Line 556:
|}
|}


== Notes on materials ==
== Cutting to engrave ==
 
A small CO2 laser cutter can cut or engrave a wide variety of materials, e.g. (some) plastics, wood, cardstock, textiles, cork, Delrin, Depron foam.
 
'''Never''' cut anything that includes '''chlorine'''. Its gas can badly damage your lungs and the machine. Without ventilation it even could kill. Other materials like ABS or HDPE can catch fire and/or melt.
 
Read more:
* [http://atxhackerspace.org/wiki/Laser_Cutter_Materials Laser Cutter Materials] (Hackerspace).
* [http://fab.cba.mit.edu/content/tools/universal_laser/ Universal Laser Cutter Tutorial] (MIT). Just read the intro.
 
=== Acrylic (plexi) ===
 
Acrylic, better known as '''Plexiglas''' and also known as Plexi, or Perspex is probably the easiest material for cutting.
There are two different types of Plexiglas – cast and extruded. Cast acrylic seems to work better.
 
It is best to place the sheet on some pieces of wood as opposed to directly putting it on the honeycomb (i.e. there will be less reflection that could cause little damages to the plexi).
 
* Chemical name: PMMA, (in french): polyméthacrylate de méthyle
 
'''Cast acrylic''' (Plexiglas GS)
* Presents a nicer surface
* Cutting is more precise
* becomes white or mat after engraving, i.e. you get a better contrast
 
'''Extruded acrylic''' (Plexiglas XT)
* is cheaper
* remains clear
* doesn't cut as nicely and sometimes even badly.
 
In other words, extruded Plexiglas is cheaper but results (both for cutting and engraving) are not great.
 
=== Cardstock, cardboard and paper ===
 
All cut well and engrave well enough.
* Cardstock is "thick paper", e.g. like birthday greeting cards.
 
* Ondulated carboard a very good prototyping material, since it is free (you always can find shipping boxes that you can tear apart) and it has a similar thickness as poplar plexiglass and plywook width (i.e. about 3mm). Make sure to use less power for cutting and single pass engraving or there could be a risk of fire. In any case, ventilation should be on.
 
* Thick paper that one can use with a laser or inkject printer can be engraved and cut. Cutting power should be low and engraving power rather high.
 
=== Wood ===
 
We had very nice experience with Wood from Wine boxes (7mm). Easy to cut in two passes, nowhere near as smelly as MDF or Plywood. Produces very few ashes compared to other two.
 
=== Engineered composite wood ===
 
Various variants of "engineered woods" are popular materials in education, since it they cheap and stable. However, they contains glue and other ingredients and may not cut as nicely as solid (non resinous) wood. In addition, these components '''may represent a health risk'''.
 
==== MDF (Medium density fiberboard) ====
 
According to [https://en.wikipedia.org/wiki/Medium-density_fibreboard Wikipedia] (10/2016), {{quotation|edium-density fibreboard (MDF) is an engineered wood product made by breaking down hardwood or softwood residuals into wood fibres, often in a defibrator, combining it with wax and a resin binder, and forming panels by applying high temperature and pressure. MDF is generally denser than plywood.}}
 
There exist variants. Again, according to Wikipedia, MDF is typically made up of 82% wood fibre, 9% urea-formaldehyde resin glue, 8% water and 1% paraffin wax and the density is typically between 500 kg/m3 and 1,000 kg/m3.
 
==== High-density fiberboard ====
 
High-density fiberboard (HDF), also called "hardboard" is, according to [https://en.wikipedia.org/wiki/Hardboard Wikipedia] (10/2016) similar to particle board and medium-density fiberboard, but is denser and much stronger and harder because it is made out of exploded wood fibers that have been highly compressed. Consequently, the density of hardboard is at least 500 kg/m³ and is usually about 800–1040 kg/m³. It is used in the furniture industry and construction.
 
HDF works well with laser cutters
 
==== Plywood ====
 
Plywood (contreplaqué in French and Sperrholz in German) includes at least three rotated layers of wood. Plywood boards are cheaper to produce than wood and keep their form. However, unlike wood, it is difficult to sand plywood to make it look again once it starts aging. According to [https://en.wikipedia.org/wiki/Plywood Wikipedia] (10/2016), Plywood is a sheet material manufactured from thin layers or "plies" of wood veneer that are glued together with adjacent layers having their wood grain rotated up to 90 degrees to one another.
 
There exist many different types, e.g.
* Softwood plywood, typically used for construction
* Hardwood plywood {{quotation|is made out of wood from angiosperm trees and used for demanding end uses. Hardwood plywood is characterized by its excellent strength, stiffness and resistance to creep.}} ([https://en.wikipedia.org/wiki/Plywood Wikipedia])
* Aircraft (or high-strengh) plywood is usually made from mahogany and/or birch.
 
For laser cutting, there are three challenges:
* Avoiding defects (e.g. hard nodes) in the inner layers
* Cut a larger sheet in a single passage (smaller lasers like ours cannot do that) and avoid too much "burning". Good quality plywood (e.g. birch) seems to be hard to cut (much harder than wood from wine boxes or MDF)
* dealing with (sometimes) rather toxic glue.
 
Usually, more layers (multi-ply) wood means better quality. According to [http://n-e-r-v-o-u-s.com/blog/?p=6042 the nervous system blog], multiple layers may include more opportunities for "bad" spots to exist and contain more glue and therefore are not more suitable for laser cutting. As result they decided to have their own three layer version built from high quality wood.
 
There are companies that sell plywood designed specifically for lasering.
 
=== Foams ===
 
Various foams can be cut, but tend to melt and produce somewhat toxic gases. Special safety measures must be taken (ventilation on) and the lens should be cleaned after each job.
 
According to [https://www.troteclaser.com/en/applications-laser/mousse-filtres/ Trotec] (10/2016), Foams made of polyester (PES), polyethylene (PE) or polyurethane (PUR) or Neopren® are well suited for laser cutting, laser engraving and laser marking. (in french: polyester (PES), polyéthylène (PE) ou polyuréthane (PUR) ou Neopren®)
 
'''Polyester'''
 
Polyester are mostly used for clothing, but some kinds of foams also seem to exist...
 
'''Polyurethane''' (PU)
 
Is the kind of foam that one can find in packaging and matresses. Typical brand names are: PUR, PU, Cellasto®, Elastocoat®, Elastoflex®, Elastofoam®, Elastolit®, Elastopal®, Elastopan®, Elastopor®, Lupranol®, Baydur®, Bayfill®, Bayflex®, Baylit®, Baymer®, Baytherm®, Desmodur® (according to [http://www.eurolaser.com/fr/materiaux/polyurethane-pur/ Eurolaser])
 
Different densities exist (measured in kg/m<sup>3</sup>) and the material is rather cheap. E.g. on Amazon.fr 200x60x3 14kg/m3 white is 6 Euros on Amazon.fr. Denser material is a bit more expensive, e.g. 200x120x3 is 16)
 
'''Polystyrene''' (PS)
 
Foams made from Polystyrenes are mostly semi-ridid, i.e. use in architectural models or publicity. Seems to be very '''inflammable'''
 
Some brand names are PS, Hostyren®, Vestyron®, Styropor®, Hostapor®, Vestypor®, SMART-X®, Elmer.
 
For example: '''Elmers''' is sold in carft stores and online, e.g. [https://www.amazon.fr/Elmers-Colored-Inches-16-Inch-Single/dp/B0141O1L6M/ref=sr_1_1?ie=UTF8&qid=1474039684&sr=8-1&keywords=Elmer%27s+Colored+Foam+Boards here]. Elmers foam is probably OK if you have a good ventilation system. It does not contain chlorine, see the [http://cdn.dickblick.com/msds/DBH_132020000.pdf MSDS]
 
'''Polyethylene'''
 
Seems to melt a lot.
 
'''To sort out'''
* Adams
* DTFB
 
=== Cloth ===
 
Most "natural" fibers like felt, hemp or cotton cut well.
 
'''Warning''' there is a danger that the print head will grab some piece of floating textile and then displace the whole thing (remember [[3D printing]]). To avoid that, make sure that the cloth is very flat, e.g. wrap it around a sheet of metal or even better tape it down with some double sided tape.
 
Some synthetic fibers also do well, but be very careful (in particular '''never''' use ''dangerous'' PVC/Vinyl)


Engraving is a bit more tricky. Fleece or felt jackets are probably best. For these, try 100% and 100% speed. Doing thinner materials without cutting out too much is difficult. Maybe use two passages with lower power ?
Let's assume that you only want to draw some lines, e.g. for a large board. This can take up to an hour of raster engraving.


Anyhow, cutting and engraving textiles is fun, but always try first with a same or very similar material before you thread your new blue jeans...
Alternative:
 
* Define another color for cutting, e.g. blue
=== polyvinyl chloride (PVC) ===
* Then set to something like power = 100 and speed = 20 '''and defocus by z=1'''. This will lower the platform and make the lines fatter.
 
According to [https://en.wikipedia.org/wiki/PVC_clothing Wikipedia], The terms "PVC", "vinyl" and "PU" tend to be used interchangeably by retailers for clothing made from shiny plastic-coated fabrics. These fabrics usually consist of a backing woven from polyester fibers with a surface coating of shiny plastic. The plastic layer itself is typically a blend of PVC and polyurethane (PU), with 100% PVC producing a stiff fabric with a glossy shine and 100% PU producing a stretchy fabric with a silky shine. A manufacturer's label may say, for example, 67% polyester, 33% polyurethane for a fabric that contains no PVC; or 80% polyvinyl chloride, 20% polyurethane with mention of the polyester backing omitted. To add to the confusion, the plastic layer is often textured to look like leather ("leatherlook", "pleather"), as opposed to smooth ("wetlook", "patent").
 
* '''Very dangerous'''. It will both damage the laser (e.g. the lens) and your lungs. You will have to particularly careful with unlabelled textiles. Do never use Vinyl sheets made for the [[cutting plotter]].


== Links ==
== Links ==
Line 553: Line 572:
=== Various tutorials and other useful texts ===
=== Various tutorials and other useful texts ===


* [http://wiki.happylab.at/w/Trotec Trotec]. Happylab "how to".
* [http://wiki.epfl.ch/lapa-studio/documents/DTS/laser%20tutorial.pdf Laser tutorial] (EPFL, for a trotec speedy 500)
* [http://wiki.epfl.ch/lapa-studio/documents/DTS/laser%20tutorial.pdf Laser tutorial] (EPFL, for a trotec speedy 500)
* [https://www.sculpteo.com/en/lasercutting/prepare-your-file-laser-cutting/ Sculpteo tutorials] (focused on designing with various tools)


=== Local (Geneva area) shops for materials to cut ===
=== Local (Geneva area) shops for materials to cut ===


* Migros Materials (local do-it-yourself shop)
* Migros Materials (local do-it-yourself shop)
** Wood and Plexi XT
** Wood, Plywood, MDF,etc.
** e.g. [http://www.doitgarden.ch/fr/bauen---handwerk/baubedarf/kunststoff/acrylglas-flach-extrudiert/ verre acrylique] (500 x 250 x 5 = CHF 12.90)
** Plexi XT, e.g. [http://www.doitgarden.ch/fr/bauen---handwerk/baubedarf/kunststoff/acrylglas-flach-extrudiert/ verre acrylique] (500 x 250 x 5 = CHF 12.90)


* Polyplast
* Polyplast
Line 574: Line 595:


* Serex
* Serex
** E.g. [http://www.serex-plastiques.ch/verre-acrylique-pmma-plexiglas-prix PLEXIGLAS XT], CHF 50 / m2 3mm and CHF 83 / m2 for 5mm
** E.g. [http://www.serex-plastiques.ch/verre-acrylique-pmma-plexiglas-prix PLEXIGLAS XT], CHF 50 / m2 3mm and CHF 83 / m2 for 5mm
 
=== Trotec online Shop ===
 
Only companies and organizations seem to be able to buy. Materials on average cost less than in local shops and are tested with Trotec machines.
 
* [https://www.gravurmaterialien.ch/ Gravurmaterialien.ch]
 
== Références ==
 
<references />


[[Category: Fab lab]] [[Category:3D]] [[Category: hardware]] [[Category: laser cutting]]
[[Category: Fab lab]]  
[[Category:3D]]  
[[Category: hardware]]  
[[Category: laser cutting]]

Latest revision as of 16:35, 9 September 2024

Introduction

This page will document the Trotec Speedy 100R that TECFA (me) that we just acquired - Daniel K. Schneider (talk) oct 2016

As far as I can tell for now, we will use this machine to create three types of objects:

  • 2D objects, e.g. badges, games and toys (created from simple SVG drawings)
  • 3D structures to assemble from 2D elements (created from simple SVG drawings), e.g. animals
  • 3D structures glued together (made from sliced 3D objects). The slicing can be done with various tools, e.g. Netfabb, Slice3R, 123D Make.

All cut parts also can be engraved, either vector engraving or raster engraving (typically from pictures).

Specifications of the 100R at TECFA

Speedy100-atmos-compact.jpg

This system easily fits into an office and it just needs two electrical standard plugs.

Speedy 100R

  • 50 W CO2 laser (Iradion tube)
  • 2 inch lens (standard)
  • 61cm x 30.5cm working surface
  • 180 cm/sec speed
  • Box size: 982 x 780 x 457 mm
  • 80 kg
  • Air cooling

ATMOS Compact exhaust fan

  • 815 x 675 x 555 mm
  • 88kg

Official home page:

Laser cutting parameters

There are several parameters that must be set (you can create profiles for that)

Basic

  • Cutting power, typically 100
  • Cutting speed, typically 1
  • Cutting pulse (faster = stronger, but more inflammable), typically 1000
  • Engraving power, typically 50
  • Engraving speed, typically 100
  • Engraving resolution, typically 500PPI
  • Material thickness, typically 2-5mm

Advanced

  • "Print file creation" parameters can define whether using the standard color scheme (e.g. hairline red for cutting and black for engraving) and how to render pictures, etc.
  • Repetition for both cutting and engraving. Some materials need 2-3 passes.

Outline of the workflow

Preparation steps

(0) Clean the lens (with a microfiber cloth or equivalent)

(1) Switch the machine on

(2) Place work piece

  • open cover
  • Place piece into upper left-hand corner, against horizontal and vertical rules

(3a) Focus laser beam (manually)

  • By default (for the mid-resolving lens) the beam is located 5.08 cm (2.0 in) below the lens.
  • Position the processing head over the work piece
  • Hang the focus tool on the external ring of the working head
  • Then, move up (by little steps) the working table

(3b) Alternatively, focus laser beam with software

  • Click the icon “focus laser” in the Trotec JobControl (make sure that material thickness, table height and lens type are OK !)

Create a graphic

  • Any vector graphic will do, since jobcontrol will work from the print file, i.e. the control software will analyse the postscript and let you configure the print from there.
  • However, we noticed that something doesn't work properly with Inkscape drawings (old 0.4x version), i.e. TroTec Job control cannot identify some vectors. Try producing a PDF first ("print to PDF file" in Inkscape), then print the file from PDF. Anyhow, make sure to install the latest version of Inkscape and read Using Inkscape for laser cutting

Preparing the print file

From your drawing or rendering software, File->Print the drawing

  • Select as printer Trotec Engraver
  • Click on Preferences
  • Define (at least):
    • Material parameters, e.g. a setting you defined for a given type and thickness of Material (these parameters, however can be changed later)
    • Algorithm (e.g. for simple vector-based cutting and engraving use color, if there are pictures, you could try Optimization, Stucki, etc.)

Then click bottom "print" icon and "print" again from the Windows software. Trotec JobControl now will open and the print file should appear in the jobs queue to the right.

Job Control software

In the Job Control software, verify or specify all the parameters

  • Establish Connection in JobControl
    • On the laser move the cutting head to the position where you plan to start
    • Position the job on the plate with a double click
  • Verify engraving material
  • Associated Power, velocity and Pulse parameters
  • Thickness (important in case you do more than one passage)
  • Color codes for engraving and cutting (check the panel to the left). Click update. If you see a warning about unidentified vectors, go back to you drawing tool and make sure that each object does have a good color (e.g. black for engraving). Inherited colors, in Inkscape for example, do not seem to work. Ungroup everything, select stuff to engrave and make sure that it has either stroke, fill or both.
  • <Double click> on the workspace to bring up the Material library where you can change all parameters.

You also can change

  • orientation of the work piece (right-click on the object)
  • orientation of the plate

Once the situation feels allright, click the Print button (lower right)

Print

  • Calibrate the height
  • Make sure that the material to cut is flat (important for textiles). Otherwise either increase power or weigh down the material. You also can use "Seklema Haftmatten" (Trotec Shop)
  • Establish Connection in JobControl
  • Verify Exhaust Ready in Engraver Control (green arrow) in the Control of the JobControl
  • Press START button (green arrow) in Job Control.

Wait

  • After printing slightly toxic materials, e.g. MDS (glues) or foam (styrene), wait at least a minute (until the aspiration ventilator stops). This will help keeping the lens clean and also help your breathing...

Preparation of drawing

Principles:

Input

  • Any 2D CAD or drawing file.
  • For cutting, the stroke of the vectors should be less than than 0.01mm (or 0.25pt), i.e. hairline of a same color. At TECFA, we use red for cutting.
  • Other elements will be engraved, depending on the settings
  • If you use the standard "Color mode" to identify objects, pick the colors from the limited set of the basic RGB colors.

Colorcode at TECFA:

  • red = cutting
  • black = engraving (simple or double, depending on the profile)
  • blue = simple engraving

Software

We suggest creating all models in SVG. That way they can be displayed directly on the web. Most drawing programs can import/export SVG

(section to be moved some day)

Online tools


Process Options and parameters - Tables for cutting and engraving

Let's recall the basic principles. Engraving depth is varied through the laser power or the speed (energy per area unit principle) For cutting, Hz settings (pulses per second) should be set to low, in particular if materials are flammable. Vector lines are color coded and for each color one can assign a cutting/engraving parameter. I.e. one could use "red" for cutting" and "greys" for engraving. A print job can include cutting, or engraving, or both.

In addition to these basic parameters, one can define so-called "process options", i.e. instructions on how to create a print file.

  • Process Mode will identify major algorithms used to transform a drawing into a "cuttable/engraveable" drawing
  • There are various options that depend on selection of "Process Mode".

To learn more about parametrization, one could look at published examples, for example:

Process options are defined before printing. Here are the steps

(1) Step 1:

  • From your application, e.g. Inkscape, Illustrator or PDF you will print your design.

(2) Step 2:

  • From the Windows print menu select Trotec Engraver Vx and then click on Preferences
  • In the Printing Preferences window, make sure that you are in expert mode (select the general tab)

(3) Steps 3 and 4: Define material settings and process options

In the Print tab you then must define the print process:

  • Select <user defined size> in size settings and tick minimize to job size and take from application. This way you can print several designs at the same time. If you leave the full dimensions (i.e. 600x300 you cannot).
  • Select material settings (you can change these later again)
  • Define the process options (these cannot be changed later, since the print driver must create the printable design)
Windows Print Options and Troctec Process Options

More details are given below.

Process Mode

Process mode identifies the type of processing, i.e. how a drawing is interpreted and "translated" for laser cutting and printing

Standard

Several design colors (at least two) will identify how a given object will be cut or engraved.

Stamp

Is used to create rubber stamps.

Relief

“This type of processing controls the laser power depending on the gray-scale value of the graphic.” [1]

This configuration requires 256 gray scale (8-bit). Lighter means less power and darker means more power.

  • white = no engraving
  • black = full power
  • levels of grey = depends.

Therefore one should use pictures or drawings with good contrast. Also, to see an effect, materials should be fairly soft so that the laser can remove enough materials in one pass.

Layer

Layer is similar to relief but works with several passes. “Gray-scale graphics are engraved in several passes. The number of passes can be set in the range from 2 to 255” (page 31), i.e. each grey value is translated to a number of passes. This allow to create stronger reliefs.

Photo

Allows to engrave high resolution pictures without prior vectorization.

Seal

Allows creating seals.

Cut

Same as standard mode, except that all non cutting objects are eliminated from the job before processing.

Other options

Engraving resolution

Resolution

defines engraving resolution in dots/inch (DPI) e.g. in dots/2.54cm2.
Recommended size is 500 in most cases. Going higher means much longer printing time and you won't see the difference with most materials. Higher also means increasing the engraving depth. As an alternative to high DPI, you also could engrave in two passes.

Cut line

  • None: Normal operation, i.e. cutting will only happend along your cut lines.
  • Rectangular: Will create a cutting line that follows the job margins (is that the document size ?)
  • Circular: Same as above, but will create a circle
  • Optimize: Creates a cutting line that is ajusted to the contour of all engraving objects. Warning: Do not use "optimized" unless you need this. Cutting along the contour doesn't make sense, usually.

Automatically created cuttin lines (rectangular, circular and optimize) are always created in red. Therefore you also should make sur the "cutting color" is set to red.

Half tones

Halftone options will convert (or not) grey-scale or color images to black and white images. Various levels of grey or color "heat" is translated to different dot sizes and pitches that will still allow recognizing the original more complex picture. This process is called dithering (Wikipedia). Not available for relief and layer processing (since these require grey levels). There are three advanced dithering algorithms (Stucki, Jarivs and Floyd Steinberg). For more information about [ dithering], read Image Dithering: Eleven Algorithms and Source Code

ordered dithering

Creates soft constrasts between brightness gradients

Stucki

Probably the most advanced Dithering algorithm for photo engraving.

Jarvis

Advanced Dithering algorithm for photo engraving

Floyd Steinberg

The first well known advanced Dithering algorithm for photo engraving

Color

Deactivites the halftoning, i.e. engravable objects will be engraved if they fit a engraving color defined in the Materials.

Black & White

Will transform each pixel to either black or white according to a threshold level

Checkboxes

  • We suggest ticking enhanced geometries and innner geometries first.

Material settings table

Since we just started with laser cutting, please consider the following very provisional ! In principle, the settings should work for a Trotec 50W CO laser... but they are by no means optimal (yet). Various materials that one could use with a CO2 Laser like the Speedy 100 are described in the laser cutting article.

Often there are different solutions that lead to similar results. Remember that laser power received is a function of power and speed, and pulse (in case of cutting)

(Maybe outdated) profiles are in this web directory (selected groups)

Material Cutting power Cutting speed Cutting Hz N cutting passes Engraving power Engraving speed N engraving passes Engraving resolution Notes
MDF 5mm 55 1.1 1000 2 50 100 2 500 2 passes reduced burning
MDF 3mm 80 1 1000 1 50 100 500
Maple Wood 5mm 80 1 1000 1 100 70 2 (is prettier) 500 To create darker engraving, reduce speed a bit. To go deeper, do 2 passages.
Plywood poplar 3mm 100 1.1 1000 1 100 100 (70) 1 (2 at 70 is prettier) 600 Very easy, since weak material.
Plywood poplar 5mm 100 0.9 (0.8 if uneven) 1000 1 100 100 (70) 1 (2 at 70 is prettier) 600 Poplar plywood is not very strong, but easy to engrave and to cut.
Plywood linden Creality (tilleuil) 10mm 100 0.32 1000 2 100 80 2 500
Plywood birch 4mm 100 1.2 (for large objects maybe a bit less) 1000 1 80 (or better 2 at 60) 100 500 Birch plywood is strong quality but difficult to laser, in particular larger than 4mm sizes.

Watch out for flames

Plywood birch 6.5mm (difficult) 80 0.5 1000 2 60 (2x) 70 500 Set correction to 15. These are minimal settings to test and some larger cuts with lots of details could fail. Result is very black and requires washing. You could put some painters tape on the cut lines to avoid blackening of the surface.
Plywood birch 6.5mm (variants) 100 0.5 - 0.6 2500 - 5000 2 80 70 500 Result is always very black and needs washing. More pulse and more power doesn't change that much. Result looks similar and flames are a bit bigger and will destroy thin elements. Also try three passes with a bit less power or higher speed.
Plexi 10mm 100 0.5 10000 2 80 100 500 Better, position the plate on top of some wooden blocks, not directly on the grid.
Plexi 5mm 100 0.8 4000 2 80 100 500 Better, position the plate on top of some wooden blocks, not directly on the grid.
Plexi 4mm 100 0.8 4000 1 80 100 500 Position the plate on top of some wooden blocks, not directly on the grid.
Plexi 3mm 100 1 4000 1 80 100 500
Plexi 2mm 100 1.2 4000 1 80 100 500
Trolase Textures 1.6 mm matte 50 0.8 4000 1 100 50-60 600 This is a bi-color acrylic plastic from TroTec, much cheaper than Plexiglass, i.e. a 60.5 x 30.5cm costs 12.20 CHF. Extra settings: Z-offset is 2 (as opposed 0) in order to make the laser a bit thicker. (2) Start position at bottom (right-click, select properties)
Trolase 0.8 mm smooth 50 1.5 1000 100 50-60 600 Z-offset = 2. Verify.
Ondulated Cardboard 75 3 1000 1 60 100 1000 Rough settings, thickness and density is widely different. If the first layer is thicker you can go with engraving P = 80
Ondulated Cardboard (cuts) 20 1 1000 1 7 3 5000 Rough settings. Engraving parameters are meant for engraving lines, i.e. cuts defined with another color ! Both speeds could be higher. Please test first with a small design.
Thick paper 0.25mm ? 30 3 1000 1 80 100 1000
Gunold Step 22 1.9 1000 1 1000 Special embroidery textile for creating patches. Set Power to 30 (instead of 22) for larger pieces. The tissue can warp and the laser will be less focused and therefore less strong
Cotton (pants) 30 3 1000-3000 1 20 100 200-300 Test this, engraving effects differ for each type of cotton. I made a Halloween mask from a cut off pant leg). Make sure to work with a low DPI (else you can create cuts that will appear later). In addition use an offset of 2 to 20mm (defocalize) and turn off the ventilator.
Wood Wine box 7mm 100 1.5 1000 2 60 70 500 Nice and easy, if the wood is light. Testing required
Heavy Wood Wine box 9.5mm 100 0.35 2000 3 40 100 2 500 Some use tougher wood, so it won't be nice and easy. Testing required. Maybe 0.23 for cutting speed.
Anodized aluminum, e.g. Laptops (this needs to be tested !) - - - - 100 ? 100 500 Not tested, probably also depends a lot on the coating. Use weaker settings for plastic cases !!
Material

Cutting to engrave

Let's assume that you only want to draw some lines, e.g. for a large board. This can take up to an hour of raster engraving.

Alternative:

  • Define another color for cutting, e.g. blue
  • Then set to something like power = 100 and speed = 20 and defocus by z=1. This will lower the platform and make the lines fatter.

Links

Models

Various tutorials and other useful texts

Local (Geneva area) shops for materials to cut

  • Migros Materials (local do-it-yourself shop)
    • Wood, Plywood, MDF,etc.
    • Plexi XT, e.g. verre acrylique (500 x 250 x 5 = CHF 12.90)
  • Polyplast
  • Serex

Trotec online Shop

Only companies and organizations seem to be able to buy. Materials on average cost less than in local shops and are tested with Trotec machines.

Références

  1. ↑ Trotec (2015), Operation Manual Trotec JobControl. Basic, Advanced, Expert. Retrieved from https://www.troteclaser.com/fileadmin/content/images/Contact_Support/Manuals/JobControl-Manual-EN.pdf, page 31
Retrieved from "https://edutechwiki.unige.ch/mediawiki/index.php?title=Trotec_Speedy_100R&oldid=78418"