Skeinforge for RapMan: Difference between revisions
m (→Temperature) |
m (→Fill) |
||
| Line 26: | Line 26: | ||
Allows to define how an object should be filled. | Allows to define how an object should be filled. | ||
* Default: OFF | * Default: OFF (put it on for solid objects) | ||
{| class="wikitable" | {| class="wikitable" | ||
| Line 34: | Line 34: | ||
| Solid Surface Thickness||Defines the number of solid layers that are at the bottom, top, plateaus and overhang||3|| | | Solid Surface Thickness||Defines the number of solid layers that are at the bottom, top, plateaus and overhang||3|| | ||
|} | |} | ||
=== Fillet === | === Fillet === | ||
Revision as of 00:36, 11 March 2010
Some mission critical stuff is missing. For now, I just verify and edit the g-code, in particular to adapt the raft for larger pieces, or to slow down printing/augment extrusion rate for pieces that I want "smooth".
Introduction
Skeinforge is a tool chain for printing 3D objects.
The purpose of this entry is to write down the most important parameters and settings for the RapMan V3.1 as installed at TECFA (each Rapman may be a different)
Some parameters
Carve
Chamber
Turn off
Clip
Comb
Cool
Fill
Allows to define how an object should be filled.
- Default: OFF (put it on for solid objects)
| Parameter | Explanation | Default | Comments |
|---|---|---|---|
| Solid Surface Thickness | Defines the number of solid layers that are at the bottom, top, plateaus and overhang | 3 |
Fillet
Purpose: Rounding of corners
- Default: OFF
Flow
The flow script sets the flow rate by writing the M108 gcode.
Default: 210
Jitter
Jitter jitters the loop end position to a different place on each layer to prevent the a ridge from forming.
Raft
Raft is a script to create a raft, elevate the nozzle and set the temperature.
| Parameter | Explanation | Default | Comments |
|---|---|---|---|
| Base Feed Rate Multiplier | Defines the base flow rate multiplier. The greater the 'Base Flow Rate Multiplier', the thicker the base, the lower the 'Base Flow Rate Multiplier', the thinner the base. | 1 | Maker it greater than the default |
Speed
Speed is a script to set the feed rate, and flow rate.
| Parameter | Explanation | Default | Comments |
|---|---|---|---|
| Add Flow Rate | Will add g-code | On | If nothing comes out of nozzle check this. |
| Feed Rate | Defines the feed rate for the shape | 16 millimeters/second | seems a bit too much. |
| Flow Rate | Defines the operating flow rate | 210 | This may be too little. I often use 400 |
| Perimeter | have higher build quality on the outside at the expense of slower build speed | 0.5 | |
| Travail feed rate | Defines the feed rate when the extruder is off | 16 | slow down for figures with lots of little pieces. |
Temperature
| Parameter | Explanation | Default | Comments |
|---|---|---|---|
| Base Temperature | Base temperature | 200 | This is much too low (ABS in my RapMan likes about 247 and 238 for the raft... |
| Interface Temperature | ??? | 200 | not enough |
| Object First Layer Infill Temperature | ??? | 200 | |
| Object First Layer Perimeter Temperature | ??? | 220 | |
| Object Next Layers Temperature | ??? | 230 | |
| Support Layers Temperature | ??? | 200 |
Links
- Download
- Tutorials, Manuals, etc.
- More Skeinforge (BitsFromBytes Blog).
- Skeinforge settings (BFB Blog)
- For ABS, the best information probably is ABS (BitsFromBytes Wiki)
- Skeinforge Fill
- Skeinforge Quicktip: Fill (outdated with respect to the interface)
- Skeinforge Carve