Silhouette Cameo
<pageby nominor="false" comments="false"/>
Introduction
The Silhouette CAMEO is a low cost home-user plotting/cutting machine. It's probably the most simple tool to get to start a simple fab lab.
According to Silhouette Cameo USA “The Silhouette CAMEO™ is an electronic cutting tool for personal use. Like a home printer, it plugs into your PC or Mac® with a simple USB cable. However, instead of printing it uses a small blade to cut paper, cardstock, vinyl, fabric and more up to 12" wide and 10 feet long. The machine also boasts a quiet motor and the ability to register and cut printed materials.”
Specifications and installation
What can it do ?
This machine can make Scrapbook pages, Cards, Custom apparel, Vinyl décor, Etched glass, Sketch designs, Temporary tattoos, Paper crafts. Technically speaking it can cut:
- Paper and cardstock
- Adhesive vinyl
- Fabric
- Heat transfer material
- Rhinestone templates
- Specialty media
A free software is included. The $50 extended Cameo software can read SVG files
Installation
- Download the latest software from http://silhouetteamerica.com/software. (This software also comes with the included CD, but it's an older version probably).
- Enter the 13 digit code if you also bought the Silhouette Studio Designer edition. This will unlock extra features
- Connect the Silhouette to your PC
- On Win 7 64-bit: Power off the Silhouette. Insert the CD in the box and install the driver which can be found on Silhouette-Studio/Driver_64_English/GDSETUP64.exe. Ignore the warnings in the installation dialog.
Vinyl cutting basics
Create or load a design
Adjust page size:
- In page panel to the right, select the size of your drawing. You can use some presets, E.g. A5 landscape.
- You can ajust the size of the drawing panel at all time. Just make sure that the design fits and that you don't waste materials.
- If this panel doesn't show, click on the upper 4th icon on top from the right.
Create a design
- For starters, we suggest typing some text
- You can select font, font-size and font variation in the Text Style panel (A icon on top
- Then, enter the text using the text tool A icon in the left tools panel.
- Readjust font size, etc. and position.
Verify page size
- I suggest to verify the page size again. Length doesn't matter, but width must be smaller than your vinyl roll's width.
Select the cut settings
In the software:
- Open the silhouette cut settings panel (3rd icon from top/right)
- Select material, e.g. Silhouette Vinyl.
- This will adjust the speed and thickness.
- It will tell how to adjust the blade setting (see below)
- It also will tell if you need a cutting mat
Cut
On the Cameo:
Notice:
- No cutting mat is needed
- You just insert the roll, if you plan to cut it before, make sure that there is some extra space with respect to the design, i.e. at least 3cm else the rollers can't move the page ....
- Rolls may not be suitable way to deliver vinyl. Since it is curbed, the loading procedure can fail. Roll the roll in the other side in order to remove some tension...
Procedure:
- Adjust the blade setting, e.g. 1 for vinyl (read p. 9 in the getting started manual)
- Release the blue lever on the right hand side
- Adjust the white rollers, i.e. move the one to the right. Before moving it, turn it so that it snaps off. This requires a little bit of force.
- Return the blue lever on the right hand side to upright position
- Insert the vinyl, color side up. Make sure to push it all to the left.
- Select load media and press enter
- Adjust (straighten). Relase the lever doing so and then close it again.
On the PC
- Click the Send to Silhouette button on the top toolbar.
- Verify the settings
- Click on (5) Cut page
Apply
- Cut the design (if not done before) of the roll. Use a knife and a cutting map.
Remove excess vinyl:
- Remove all the negative (not used vinyl).
- Hold down the stuff you want to keep by pressing with a finger or an other soft item such as the rubber end of a pencil. Peeling off the not wanted stuff isn't as easy as in the videos ...
- Use a hook (available in the starter kit) to remove small parts if necessary.
Apply transfer paper to design:
- Cut a transfer paper sheet in roughly the same size (else you will have to apply each item manually and that can go wrong)
- Remove the cover
- Apply it starting carefully from one end. It's best to apply it without any rotation. This way aligning the design to a surface will be easier.
- Smoothen it with the scraper. Make sure to apply some force so that it is flat and that it sticks
- Then lift off the design. It should stick to the transfer paper
Apply the deisng to a surface
- Draw two points for alignment or find another procedure
- Stick it slowly starting from one end (You won't have many attemps)
- Then smoothen with the scraper. Apply force and do it repetitively in both direction
- Peel the transfer paper off
- Enjoy ....
Links
Official
Reviews and ideas
- Silhouette CAMEO by by AshleyAnn.
- Silhouette Cameo Guide (Tips, Projects and more)
The Cameo and other vinyl cutters in Fab Labs
Sharable designs
- The 'Vinyl Cutter' System (Thingiverse). Includes a small list of things.
- OpenClipArt (you must own the SilhouetteStudio Designer Edition, $50).