InkStitch - hotfix

Draft

Objectives

• Create patterns for hotfix

• Quality: draft

• Difficulty: avanced

Principles of hotfix

Hotfix or (hotfix stones) are decorations like rhinestones, rhinestuds, nailheads, etc. that can be glued on textiles or other materials by heating them. This article will explain how to create designsd with rhinestones, i.e. flatback hotfix stones, using InkScape and optionally Ink/Stitch

Hotfix sizes SS34, SS20 and SS16

Sizes Rhinstones come in many different sizes.

• The most popular sizes are 4mm (16ss), 3mm (10ss) and 7mm (34ss).
• SS16 stones allow fairly well filled lettering or other details and manipulating these is not too much of a pain. Working with small SS10 stones allows for more "detailed" design, but is a bit more painful.
• Working with smaller ones than SS10 (3mm, e.g. SS6 (2mm) is difficult !
• SS20 (4.6 to 4.8mm depending on the make) or bigger are easy to use, e.g. for large lettering or larger fills

We distinguish four methods to design with rhinestones

• Method 1: Glue stones individually with a hotfix applicator on the tissue, i.e. some kind of soldering iron with and end that fits on top of a rhinestone (cheap). For positioning you could use a thin template.
• Cut out the template with a laser cutter or a cutting plotter. Glue a sheet of something (e.g. thick paper) underneath. Then fill the template with rhinestones by pouring a pile on the template and then using a brush. You the can either transfer the stones to a textile using a transfer sheet. Thickness of template should be 0.5mm for smaller stones, but it can be higher for larger stones (e.g. SS16 and SS24). Then use a heat press, e.g. 30 seconds for 160 - 200 degrees to glue.
• Method 3: Is similar to method 2. Instead of creating a template with a bottom, just glue the template with to the textile (or make it stick otherwise), then fill, then put it the heat press for 20 seconds a 200 degrees. Make sure that the template is not too thick.
• Method 4: Buy a stone setting machine that can place hotstones (expensive) on a transfer sheet. Then put the transferred sheet into a heat press.

See the Hotfix stone for details.

Methods for creating cutout patterns

Unless you got a stone setting machine or a lot of time to loose, you will have to create templates that allow positing the stones. You can create these templates with either a vinyl cutter or a laser cutter. Cutout patterns define where the laser or vinyl cutter will create holes for the rhinestones.

We recommend using 0.5mm cardboard for SS16 and SS20 stones and 1mm cardboard for bigger ones. SS16 stones also can used with a 1mm cardboard, but filling the holes will be a bit more difficult.

Alternatively you can buy so-called template sheets, e.g. "Rhinestone sheet set" from Brother that will also include transfer sheets. Some products allow for easier brushing.

Fill manually a polygon with circles

• Draw a circle, e.g. 4mm. Make sure to get the size right, because later scaling with precision will be more difficult.
• Copy/paste the circle and place the circles manually with polygones
• A quick method is to use the tiling method below, create a copy, select a subset, move in place, and delete the ones that do not fit into the polygon

Using tiles

• Create a circle
• Create a large tile of these circles
  • (en) Edit -> Clone -> Create tiled clones
  • (fr) Edition -> Cloner -> Créer un pavage de clones
  • You can change translations
• Combine all the clones (CTRL-K)
• Add a polygon (contour only), move it below de tile of circle in the stack, make a copy (to use as outline in embroidery)
• Select polygon and tiles
• Path -> Difference
• Path -> Break a part (CTRL-SHIF-K)
• Remove objects that you do no want. Copy/Paste and/or move circles.

Using tiles to fill an object with circles

Regular tile distribution

Tile distribution - result (somewhat misplaced template)

Scattering

This method can be used to distribute circles along a path.

(a) In order to fill a surface:

• Parametrize contour fill without underlay and without underpath
• Define wide spacing, e.g. 4.4mm for 4mm stones, change entry point if needed
• Select just this object and create a stitch plan, copy the stitch plan to another layer, fix it if needed, smooth first (ctrl-L).
• Draw a circle (e.g. 4mm) and put it on top of the stack somewhere
• Menu (fr) Extensions -> Générer à partir du chemin -> Distribuer suivant un chemin
• Select both the stitch plan and the circle, configure distances, e.g. 0.2 and go. You may have to move the result.
• Move misplaced holes, start by using the overlap tool in the align and distribute panel.
• save.

Alternatively, you also could do this with a tatami fill. However, the lines of circles will be aligned randomly, which is not optimal for dense fills.

(b) In order to fill a line (much easier)

• Draw a circle (e.g. 4mm) and put it on top of the stack somewhere
• Menu (fr) Extensions -> Générer à partir du chemin -> Distribuer suivant un chemin
• Select both the line and the circle, configure distances, e.g. 0.25 and go. You may have to move the result.
• Move misplaced holes and save.

Example using the params of above:

Preparation: Contour fill for hotfix holes generation with "Scatter along path" (Distribuer le long d'un chemin)

Hotfix holes generation with "Scatter along path" (Distribuer le long d'un chemin)

Raw results of the two operations.

hotfix holes generation with "Scatter along path" (raw result)

hotfix holes generation with "Scatter along path" (raw result)

Spray

This method is fairly efficient for medium sized objects but you can not achieve densely packed regular patterns

• Create and select a circle
• Then with a steady hand spray the circle using the following parameters (may need some adjustments)
  • Spray clones (fr: pulvériser des clones de la selection initiale)
  • Width (fr: largeur): a bit wider than the circle, e.g. for 4mm use 12
  • Quantity (fr: Quantité) : 100
  • Spread (fr: Eparpiller): 1
  • Apply on transparent zones (fr: Appliquer sur les zones transparentes): checked
  • No overlap of colors (fr pas de cheveauchement entre couleurs): Checked. (You many turn this off if do not mind touching the borders of underlying objects
  • No overlap - distance = 110 (this can be off if the overlap of colors is on).

The spray is a bit sluggish, if it stops spraying, make sure that you are no spraying on top of somethings, and restart.

Using the spray to fill an object with cercles

Result with hotstones (version 1 with some mistakes)

Once you are done, you can, if you like, optimise distribution. Select all clones and open the alignement tool.

• In the Organisation (fr: Organiser), click on Spread (fr: éparpiller). You can do this several times. Alternatively use another algorithm or adjust by hand.
• Then at the bottom, define minimal distances: E.g. H=3 and V=3 (click on the little icon to the right)

Methods that do not work

Using fill patterns

• Draw a circle, e.g. 4mm. Make sure to get the size right, because later scaling with precision will be more difficult.
• Create a fill pattern from this circle
  • Object -> Pattern -> Objects to pattern
  • Objet -> Motif -> Objets en motif (fr.)
  • The result will show as fill pattern in the fill panel
• Fill a polygon with the pattern
  • Object -> Fill and Stroke ... -> Fill ; Select the pattern icon
  • (fr) Objet -> Fond et Contour ... -> Fond (fr.) ; Sélectionnez l'icone "motif"
• In the Fill and Stroke panel adjust the distances, e.g. 20% = 0.8mm in our case.

That type of pattern can be cut with a machine that accepts bitmap input. For a typical laser cutter, the file must be exported as high resolution PNG image, then vectorize with center lines.

Pattern along path

This strategy profits from the idea that Ink/Stitch does create lines of stitches for its fills and that these lines can be used to distributed circles to position the stones..

• Select a fill
• Parametrize a tatami or other type of fill without underlay and without underpath
• Define wide spacing, e.g. 5 mm for SS10 (3mm stones), change entry or exit point if needed
• Select just this object and create a stitch plan, copy the stitch plan to another layer, fix if needed
• Draw a circle and copy it (CTRL-C)
• Path -> Path Effects...., select Pattern along Path
• (fr: Chemin -> Effets de chemin ...., choisir motif suivant un chemin
• Pattern source = link (icon to the right) (fr:) Source du motif = Lier chemin contenu dans le presse papiers
• Pattern copies = repeated (fr:) Copies du motif = répété.
• Spacing = 1 (fr: Espacement) = 1)

The result is not brilliant, the circles are distorted, even when lines are smoothed.