Fokoos Odin-5 F-3: Difference between revisions
mNo edit summary |
m (→Specifications) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 4: | Line 4: | ||
The Fokoos Odin-5 F-3 is a low-cost printer made by [https://www.fokoostech.com/ Fokoos] | The Fokoos Odin-5 F-3 is a low-cost printer made by [https://www.fokoostech.com/ Fokoos] | ||
The author of this article bought one in fall 2022. At half its price (200 Euros) I consider it a very good buy. Assembly and calibration was very quick (about 15 minutes for unpacking and assembly) and 10 minutes for calibration of the bed. I did not make any modifications since it does its job (mostly printing LEGO/Duplo compativles or some simple household appliances). | The author of this article bought one in fall 2022 at Fnac (France). At half its price (200 Euros) I consider it a very good buy. Assembly and calibration was very quick (about 15 minutes for unpacking and assembly) and 10 minutes for calibration of the bed. I did not make any modifications since it does its job (mostly printing LEGO/Duplo compativles or some simple household appliances). | ||
It prints TPU, PLA and PETG without any problems. However, the glassbed requires "hairspray" to make the PETG and the PLA stick well. To remove prints I use a hammer (slight tap) once the bed is cooled down. | It prints TPU, PLA and PETG without any problems. However, the glassbed requires "hairspray" to make the PETG and the PLA stick well. To remove prints I use a hammer (slight tap) once the bed is cooled down. | ||
<gallery> | <gallery heights=300 widths=300> | ||
fokoos-castle-PLA-3-5mm.jpg|3.5mm PLA+ Duplo compatible strong hold (for marble run) | fokoos-castle-PLA-3-5mm.jpg|3.5mm PLA+ Duplo compatible strong hold (for marble run) | ||
fokoos-marble-run-3-5mm.jpg|3.5mm PLA+ Marble run | fokoos-marble-run-3-5mm.jpg|3.5mm PLA+ Marble run | ||
fokoos-PETG-clamps.jpg|PET-G household appliances | fokoos-PETG-clamps.jpg|PET-G household appliances | ||
</gallery> | </gallery> | ||
== Specifications == | |||
* 235 x 235 x 250mm build volume | |||
* (Proprietary) direct extruder with a volano 0.4mm nozzle | |||
* Nozzle max temp = 260 | |||
* Bed max temp = 120 | |||
* Supported filament: PLA/PLA+/TPU/ABS/PETG | |||
* Official slicer: FOKOOS Slicer based on Ulimaker Cura | |||
* Typical print speed for PLA: 80mm/s and less for walls (max speed is 300) | |||
== Liens == | == Liens == | ||
Latest revision as of 16:24, 14 April 2023
Introduction
The Fokoos Odin-5 F-3 is a low-cost printer made by Fokoos
The author of this article bought one in fall 2022 at Fnac (France). At half its price (200 Euros) I consider it a very good buy. Assembly and calibration was very quick (about 15 minutes for unpacking and assembly) and 10 minutes for calibration of the bed. I did not make any modifications since it does its job (mostly printing LEGO/Duplo compativles or some simple household appliances).
It prints TPU, PLA and PETG without any problems. However, the glassbed requires "hairspray" to make the PETG and the PLA stick well. To remove prints I use a hammer (slight tap) once the bed is cooled down.
3.5mm PLA+ Duplo compatible strong hold (for marble run)
3.5mm PLA+ Marble run
PET-G household appliances
Specifications
- 235 x 235 x 250mm build volume
- (Proprietary) direct extruder with a volano 0.4mm nozzle
- Nozzle max temp = 260
- Bed max temp = 120
- Supported filament: PLA/PLA+/TPU/ABS/PETG
- Official slicer: FOKOOS Slicer based on Ulimaker Cura
- Typical print speed for PLA: 80mm/s and less for walls (max speed is 300)
Liens
- https://www.fokoostech.com/
- Facebook group (official): https://www.facebook.com/groups/fokoos
- Group Facebook: https://www.facebook.com/groups/735311000476593